User Tools

Site Tools


glossary:glossary_o

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
glossary:glossary_o [2013/04/11 04:32] – [OpenLCB] dpharrisglossary:glossary_o [2021/08/08 05:20] (current) – Moved the entry to OP to make it alphabetical Wayne
Line 7: Line 7:
  
  
-Circuit diagram of Darlington configuration     \\ In electronics, the Darlington transistor is a semiconductor device which combines two bipolar transistors in tandem (often called a "Darlington pair") in a single device so that the current amplified by the first is amplified further by the second transistor. This gives it high current gain (written β or hFE), and takes up less space than using two discrete transistors in the same configuration. The use of two separate transistors in an actual circuit is still very common, even though integrated packaged devices are available. +Circuit diagram of Darlington configuration \\ {{:glossary:2803-schematic.png?nolink& |}} {{ :glossary:2803-package.png?nolink&200|}} In electronics, the Darlington transistor is a semiconductor device which combines two bipolar transistors in tandem (often called a "Darlington pair") in a single device so that the current amplified by the first is amplified further by the second transistor. This gives it high current gain (written β or hFE), and takes up less space than using two discrete transistors in the same configuration. The use of two separate transistors in an actual circuit is still very common, even though integrated packaged devices are available.\\ \\ \\ \\ \\ \\ \\ \\ \\ **[[kits:88:outputdrive|ULN2803]]** package used as the output stage of several MERG Kits. \\ \\ \\ 
  
 +For new designs the {{ :glossary:tbd62083apg_datasheet_en_20160511-769640.pdf |TBD62083}} is recommended, this uses [[:glossary:glossary_f#FET|FET]]- Field Effect Transistor technology.\\ 
 +{{:glossary:tbd62083-pinout.png?direct&400|}}{{:glossary:tbd62083-circuit.png?direct&400|}}
 ===== Ohms ===== ===== Ohms =====
  
  
-Definition: >An ohm is a resistance that produces a potential difference of one volt when a current of one ampere is flowing through it.     \\ 1 ohm 1volt/amp (1 Ω V/A+Definition: >An ohm (SI symbol Ω but commonly is R) is a resistance that produces a potential difference of one Volt when a current of one Ampere is flowing through it. 10 Ω resistor can be represented as 10R. Ohms law formula: voltage (V) amps (I) x resistance (R) or V=I.R or I=V/R or R=V/I
  
 +===== OP =====
 +
 +Context sensitive:
 +OP - Original Poster - The person starting a topic, thread or discussion.\\ 
 +OP - Original Post - The first post in a topic, thread or discussion.\\ 
 +OP - Original Post - The first post made by a particular person in a topic, thread or discussion.\\ 
  
 ===== Op amp ===== ===== Op amp =====
Line 25: Line 32:
  
  
-Open-collector configuration In an integrated circuit, an output scheme utilizing no internal pull-up resistor. Wired-OR outputs can thus have opposite states without risk of damage to the device. +Open-collector configuration In an integrated circuit, an output scheme utilizing no internal pull-up resistor. Wired-OR outputs can thus have opposite states without risk of damage to the device.\\  
 +An example of this type of device can be seen above under [[glossary_o#octal_darlington_arrays|Octal Darlington Arrays]]
  
 ===== OpenLCB ===== ===== OpenLCB =====
 +{{ :lcb:logo-ajs-dph.png?100|}}
  
-Refers to the Open Layout Control Bus, a publicly developed MRR accessory bus which is designed to work along side a traction bus, such as [[glossary_d#DC Control|DC]] or [[glossary_d#DCC Digital Command Control|DCC]].  It uses a variety of physical buses, including CAN, Ethernet and Wifi.  It is the basis for [[glossary_n#NMRAnet|NMRAnet]].  See: [[http://openlcb.org|OpenLCB website]].+Refers to the [[https://merg.org.uk/merg_wiki/doku.php?id=lcb:start&#openlcb|Open Layout Control Bus]], a publicly developed MRR accessory [[glossary_b#bus|bus]] which is designed to work along side a traction bus, such as [[glossary_d#DC Control|DC]] or [[glossary_d#DCC Digital Command Control|DCC]].  It uses a variety of physical buses, including CAN, Ethernet and Wifi.  It is the basis for [[glossary_l#Layout Command Control|Layout Command Control™]].  See: [[http://openlcb.org|OpenLCB website]].
 ===== Optical detector ===== ===== Optical detector =====
  
  
-Optical detector: Anintegrated-circuit (ICthat provides light-to-voltage conversionIts direct-current output voltage is proportional to the intensity of light impinging on its sensor. +These comprise of a light source, a light sensor and a comparator. The light could be visible, UV (rareor IR (common). The light source can be ambient light (rare), a light bulb or a light emitting diode (common). The light sensor converts light to an electrical signal and could be a photo cell, a light sensitive semiconductor diode or transistor or a light dependent resistor (LDR)The object being detected is arrange to either interrupt the light beam getting to the sensor or reflects some light back to the sensor. The sensor output is compared to a threshold and that output is the indication of the object being detected or not.
  
 ===== Opto-isolator ===== ===== Opto-isolator =====
Line 41: Line 48:
  
 A light-emitting diode (LED) or infrared-emitting diode (IRED) and a photodiode combined in a single package with a transparent gap between them. The LED or IRED converts an electrical signal to visible light or IR; the photodiode changes the visible light or IR back into an electrical signal. This device eliminates interstage impedance reflections that can plague systems that employ electronic coupling. Even the most drastic changes in load impedance have no effect on the impedance “seen” by the signal source. The devices can also protect expensive equipment against electrical transients; for example, in telephone-line modems used with personal computers. A light-emitting diode (LED) or infrared-emitting diode (IRED) and a photodiode combined in a single package with a transparent gap between them. The LED or IRED converts an electrical signal to visible light or IR; the photodiode changes the visible light or IR back into an electrical signal. This device eliminates interstage impedance reflections that can plague systems that employ electronic coupling. Even the most drastic changes in load impedance have no effect on the impedance “seen” by the signal source. The devices can also protect expensive equipment against electrical transients; for example, in telephone-line modems used with personal computers.
 +
 +===== OR =====
 +OR [[logicgates#or|Logic Gate]]\\ 
  
  
Line 52: Line 62:
  
  
-An instrument thatpresents the pattern representing variations in an electrical quantity for visual inspection on a Cathode Ray Tube (CRT) +An instrument that presents the pattern representing variations in an electrical quantity for visual inspection on a Cathode Ray Tube (CRT) but these days on a computer screen.
  
glossary/glossary_o.1365654742.txt.gz · Last modified: 2014/11/11 13:27 (external edit)

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki